Automotive hail repair complete guides: For dents that are fairly small and not deep, a dent repair kit may be an inexpensive and simple solution. These kits are available at any auto parts store and tend to be very user friendly — instructions are always included. The best part is that they usually cost under $40. Most include several stems for various sized dents, a glue gun and a knockdown tool. You may be surprised at how well the kit works and how professional the result looks. We don’t recommend this kit for large, deep dents — you might cause even more damage trying to fix those with a kit.

First let’s begin with some car paint care tips: Another way to fix the small dents is parking your car in a sunny area. This is an effective way that most of car enthusiasts all know. By doing this way, the metal will heat up and expand. As the car surface expands, the shallow and light dents will pop out. The longer you park your car in a sunny area, the more likely this way will work.

When done correctly, your paint should feel so silky smooth it will force a smile across your face; truly like waxed glass! Traditional washing, polishing, and waxing will not remove these embedded pollutants. They need to be removed occasionally as they build-up on your cars paint. There are numerous products available to remove these pollutants. See Clay Bar for the simplified way to arm yourself with full understanding and choosing a quality Clay Bar Kit. The decontamination process will take place on a freshly washed car after all the superficial dirt has been washed away first.

Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.

Undercoating: Although waxing the car and polishing it produces good results, you need to protect the car from long term damage by undercoating and rust-proofing it. When the car metal is oxidized, rust sets in and destroys the surface of the car. To avoid this, you should consider rust-proofing the vehicle, particularly if you reside in a state where the humidity is high. See extra details on Auto Decals & Lettering Colorado Springs.

The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.